Headstock Part D

Have you seen a man hasty with his words? There is more hope for a fool than for him.

Quite a long gap since my last post. Quite unintentional. All of us who are caught in the vicious, selfish claws of this world, have our time devoured by the Money Men. But, they themselves are enslaved by their god, Profit. It’s 2014; we’ve learned nothing over the past few thousand years.

Ho hum. In the workshop, I’ve managed to grab a few hours here and there, and so, although I’m behind in my plan to get this finished by the end of July, I’m still making progress. I’m behind with my posts, but not that far behind with the Lathe itself.

In the last post, I finished cleaning the Headstock Assembly. This post describes fettling it a bit, reassembly and reinstalling.

To begin, I gave the spindle a smooth over with 2500g Wet and Dry paper (silicone carbide paper) lubricated with the VG32 oil. Hopefully this will make all the parts slide back on more easily.

I bolted the Backgear Key on to the 65T Backgear…

20140727-151446-54886819.jpg
…then pushed that back onto the Spindle…

20140727-151523-54923413.jpg
It engages with a key to stop it turning on the Spindle and is secured by a grub screw. Before I could put the Vee Cone Pulley Assembly onto the Spindle, I smoothed out it’s inner bronzy surface with the 2500 and oil, doing the same to the inner surface of the Distance Sleeve, like this…

20140727-151748-55068921.jpg
The Distance Sleeve was a tight fit, so needed some persuasion. I rigged up a jig in my vise, and used the white rubber Persuader to get it seated correctly…

20140727-152459-55499393.jpg
On the iPad in that picture is another picture of the Spindle Assembly before dismantling. I’m using that to aid in location during assembly.

As these parts get more complicated, I’m finding it crucial to think even more carefully about what photos I need to take as I dismantle things. It’s already paying off. This Headstock reassembly proved straightforward as a result.

The Thrust Bearing, Thrust Washer and Locking Collar all went on easily. The 25T Gear on the end, which needed effort to remove, went on quite easily after it’s inner surface was smoothed with 2500 and oil. Here’s the complete Spindle Assembly…

20140727-153525-56125427.jpg
Turning to the Headstock body, I smoothed the insides with 2500 and oil..

20140727-154001-56401165.jpg
…making it easy to push the Backgear Eccentric Assembly back in…

20140727-154112-56472150.jpg
This Backgear Eccentric Assembly needs to be free to rotate and is rotated by this lever which I’ve bolted back on…

20140727-154431-56671404.jpg
Pulling on the knob retracts a plunger which allows the lever to be moved to one of two positions. One of the two plunger mortices can be seen. This, the 21/56T Backgear Cluster…

20140727-154719-56839814.jpg
…is then rotated up or down by the Backgear Eccentric Assembly, engaging with the 65T Backgear Assembly and the Vee Cone Pulley Assembly. The purpose seems to get the 65T Backgear to run slowly. This next picture might help…

20140727-164511-60311869.jpg
AB Vee Cone Pulley Assembly
CD 65T Backgear Assembly, permanently connected to S
EF 21/56T Backgear Cluster, free to rotate on…
G Backgear Eccentric Assembly, operated by…
H Backgear Lever
S Spindle

Here’s how drive is transmitted. A belt from the Motor arrives at the Pulley A, which turns gear B. If Backgear Key C is retracted – as it is in the picture – and Lever H is in the down position thereby keeping EF disengaged, then AB will spin, driving nothing.

If C is engaged with B, and Lever H is down, then B is connected to D, the 65T Backgear, which will turn Spindle S at the same speed as the Pulley.

If C is retracted and Lever H is up – as it is in the picture – then EF is engaged and drive is transmitted through B to E to F to D, turning S at a much slower speed than Pulley A.

However, if C is engaged and Lever H is up, then the Spindle S is locked and won’t turn.

I’m glad we’ve cleared that up. This is me fitting one of the bronzy (we never really got to the bottom of that, did we?) tumbler gears to the Tumbler Reverse Lever…

20140727-171119-61879565.jpg
Once the Tumbler Reverse Stud is fitted…

20140727-171048-61848216.jpg
…the Tumbler Reverse Lever, carrying the two bronzy Tumbler Gears is fitted onto the Stud, followed by the Tumbler Sleeve Gear…

20140727-171608-62168499.jpg
Had enough? Me too…

Advertisements